Installation and maintenance methods of unloading conveyor
Installation method of unloading conveyor:
-Before installing the unloading conveyor, check whether all its components are intact and undamaged, especially whether there is damage or deformation to the motor, reducer, chain, scraper, etc.
-When installing the unloading conveyor, it should be ensured that it is horizontal or has a certain inclination angle, and cannot be too large or too small to avoid affecting the conveying effect or causing blockage.
-When installing the unloading conveyor, it should be tightly connected to upstream and downstream equipment to ensure that dust does not leak out. If there are supporting equipment such as plug-in valves or flip valves, they should be installed first and operated in the correct switching sequence.
-When installing the unloading conveyor, attention should be paid to electrical connections and grounding to avoid short circuits or leakage. The power voltage should match the rated voltage of the motor, the power cord should have sufficient cross-sectional area and length, and the electrical control cabinet should be installed in a position that is easy to operate and observe.
Maintenance method for unloading conveyor:
-Before using the unloading conveyor, check whether all its components are normal, especially the chain, scraper, bearings, etc., for looseness or wear. If there are any abnormalities, replace or adjust them in a timely manner.
-When using the unloading conveyor, attention should be paid to its operation. If there are abnormal phenomena such as noise, vibration, temperature rise, etc., it should be stopped in a timely manner for inspection and troubleshooting.
-When using the unloading conveyor, the reducer should be regularly lubricated and cleaned of oil stains. The oil quantity of the reducer should be kept between the oil markings, and the oil quality should be clean and free of impurities. If insufficient or deteriorated oil is found, it should be replaced in a timely manner.
-When using the unloading conveyor, dust and debris should be regularly cleaned to avoid blocking or affecting the conveying effect. If there is dust adhering to the chain or scraper, it can be removed with a soft brush or compressed air. If there are hard objects mixed between the chains or scrapers, iron hooks or other tools can be used to remove them.
-When using the unloading conveyor, it is necessary to avoid overload or no-load operation to avoid damage to the motor or reducer. If the current is found to be too high or too low, the conveying volume should be adjusted in a timely manner or the operation should be stopped.
-When stopping the use of the unloading conveyor, downstream equipment should be turned off first, then the discharge conveyor should be turned off, and residual dust should be removed. If there are supporting equipment such as plug valves or flip valves, they should be operated in the correct order of opening and closing.
-Before installing the unloading conveyor, check whether all its components are intact and undamaged, especially whether there is damage or deformation to the motor, reducer, chain, scraper, etc.
-When installing the unloading conveyor, it should be ensured that it is horizontal or has a certain inclination angle, and cannot be too large or too small to avoid affecting the conveying effect or causing blockage.
-When installing the unloading conveyor, it should be tightly connected to upstream and downstream equipment to ensure that dust does not leak out. If there are supporting equipment such as plug-in valves or flip valves, they should be installed first and operated in the correct switching sequence.
-When installing the unloading conveyor, attention should be paid to electrical connections and grounding to avoid short circuits or leakage. The power voltage should match the rated voltage of the motor, the power cord should have sufficient cross-sectional area and length, and the electrical control cabinet should be installed in a position that is easy to operate and observe.
Maintenance method for unloading conveyor:
-Before using the unloading conveyor, check whether all its components are normal, especially the chain, scraper, bearings, etc., for looseness or wear. If there are any abnormalities, replace or adjust them in a timely manner.
-When using the unloading conveyor, attention should be paid to its operation. If there are abnormal phenomena such as noise, vibration, temperature rise, etc., it should be stopped in a timely manner for inspection and troubleshooting.
-When using the unloading conveyor, the reducer should be regularly lubricated and cleaned of oil stains. The oil quantity of the reducer should be kept between the oil markings, and the oil quality should be clean and free of impurities. If insufficient or deteriorated oil is found, it should be replaced in a timely manner.
-When using the unloading conveyor, dust and debris should be regularly cleaned to avoid blocking or affecting the conveying effect. If there is dust adhering to the chain or scraper, it can be removed with a soft brush or compressed air. If there are hard objects mixed between the chains or scrapers, iron hooks or other tools can be used to remove them.
-When using the unloading conveyor, it is necessary to avoid overload or no-load operation to avoid damage to the motor or reducer. If the current is found to be too high or too low, the conveying volume should be adjusted in a timely manner or the operation should be stopped.
-When stopping the use of the unloading conveyor, downstream equipment should be turned off first, then the discharge conveyor should be turned off, and residual dust should be removed. If there are supporting equipment such as plug valves or flip valves, they should be operated in the correct order of opening and closing.